Our goal is to provide you with a quick access to the content of the user manual for Dell UltraSharp FP. Using the online preview, you can quickly view the contents and go to the page where you will find the solution to your problem with Dell UltraSharp FP. If looking through the Dell UltraSharp FP user manual directly on this website is not convenient for you, there are two possible solutions:. Many people prefer to read the documents not on the screen, but in the printed version. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual. Below you will find previews of the content of the user manuals presented on the following pages to Dell UltraSharp FP.
|Published (Last):||9 February 2019|
|PDF File Size:||13.5 Mb|
|ePub File Size:||13.48 Mb|
|Price:||Free* [*Free Regsitration Required]|
Quick Links. See also: Service Manual. Dell FPc. Table of Contents. Page 2: Table Of Contents Dell FPc Table of contents Table of contents 02 Revision List Important Safety Notice 04 1. Monitor Specifications 2. LCD Monitor Description 06 3. Operation instructions 3. The service procedures recommended by Dell and described in this service manual are effective methods of performing service operations. The power board will provide AC to DC Inverter voltage to drive the backlight of panel and the main board chips each voltage.
The other control buttons are located at front panel of the monitor. By changing these settings, the picture can be adjusted to your personal preferences. Page 8 Use the Input Select button to select between two different video signals that may be connected to your monitor. Depending upon the selected input, one of the dialogs shown below will scroll continually.
Page 9 Use to mount the monitor. Behind attached base plate Barcode serial number label Refer to this label if you need to contact Dell for technical support. Security lock slot Use a security lock with the slot to help secure your monitor. Dell Soundbar power connector Connect the power cord for the Soundbar optional. The changes are also saved if you change the settings and then wait for the OSD menu to disappear. Auto Adjust Even though your computer recognizes your monitor on startup, the Auto Adjustment function optimizes the display settings for use with your particular setup.
Select to activate automatic setup and adjustment. The following dialog appears This color setting is typically used for text based applications spreadsheets, programming, Normal text editors, etc. Select No - to unlock and allow user access to all applicable settings. Reset the OSD menu options to the factory-preset values. Occasionally, no warning message appears, but the screen is blank. This could also indicate that the monitor is not synchronizing with the computer.
Turn off your computer and disconnect the power cable. Connect the USB cable that was included with your monitor to the computer and the upstream USB connector on the monitor. Page 22 Dell FPc 4. Block Diagram 5. Page 25 Dell FPc Schematic Diagram 6. Page 31 Dell FPc 3. Page Layout Dell FPc 7. PCB Layout 7. Page 41 Dell FPc Cm Note: Firstly, put the monitor on a soft, flat and clean surface, wear gloves.
Page 44 Dell FPc 3. Take off the bezel Remove rear cover : Turn over the monitor as the Fig, hold the rear cover, and then slightly remove it. Remove the shield : 1. Remove the 4 screws by Torque B Page 45 Dell FPc 2. Remove the 5 screws by Torque B or by manual 4. Page 46 Dell FPc 5. Push the main shield as the arrowhead direction Disconnect the connector pin: Disconnect the connector pin between key and main boards Install: Lay the KEPC cable as the figure showed Remove the 7 screws by Torque B 2.
Disconnect the connector wire Page 48 Dell FPc 3. Page 49 Dell FPc 4. Disconnect the wire holder Install: Lay the cables as the line direction Remove the power board : Remove the 5 screws by Torque Page Maintainability Dell FPc 9.
Maintainability 9. Voltage meter 2. Oscilloscope 3. Pattern Generator 4. LCD Color Analyzer 5. Service Manual 6. User Manual No power No power Press power key and look if the U is normal Check Correspondent Check Correspondent component. Page 56 Dell FPc 9. Page 58 Dell FPc 9. Replace Button Switch Is Keypad board normally? Replace Keypad Board Check main board White balance, Luminance adjustment Approximately 30 minutes should be allowed for warm up before proceeding White-Balance adjustment.
Before started adjust white balance, please setting the Chroma MEM. Channel 3 to K colors, MEM. Channel 4 to K colors, MEM. Page 60 Dell FPc ISP Instruction Double-click the Install software Select the folder where you would like Genesis Gprobe 5 to be installed Completing the Genesis Gprobe 5 setup wizard Note: After finishing the installation, you must restart the PC.
Page 64 Dell FPc B. Next, install the Update software Completing the update 1 for Genesis Gprobe 5. Page 67 19TLB4. Page 69 Dell FPc 7. Select Exit to the upper menu after completing the adjustment. Page 70 Dell FPc Notes: 1. Make sure the system time of PC is in accordance with the real time before writing. Definition Of Pixel Defects Type 1. Page Dell FPc Type 2. Page Dell FPc Page Dell FPc Type 4. Print page 1 Print document pages. Cancel Delete. Sign In OR.
Don't have an account? Sign up! Restore password. Upload from disk. Upload from URL.
Dell 1907FPc Service Manual
If you found this page, you probably have a problem and you need a user manual for the device Dell UltraSharp FP. Be sure to check that it is the user manual to exactly the device that you are looking for. A user manualDell UltraSharp FP is taken from the manufacturer, a Dell company - it is an official document, so if you have any doubts as to its contents, please contact the manufacturer of the device Dell UltraSharp FP directly. You can view the user manualDell UltraSharp FP directly online or save and store it on your computer.
Dell UltraSharp 1907FP Quick Setup Manual
Dell UltraSharp 1907FP user manual